Simulations of Brush Contacts of Homopolar Motor/Generators
Time-dependent distributions of electromagnetic force and heating were studied.
A computational- simulation study of distributions of electric current and temperature in brushes and slip rings in two model homopolar- motor/generator configurations was performed in support of the development, by the U.S. Navy, of a superconducting homopolar motor/generator (SCHPMG) machine for ship propulsion. Electrical-contact performance (more specifically, brush/slip-ring contact performance) is a limiting factor in the performance of an SCHPMG machine. The present study and similar studies are needed to gain understanding of brush/slip-ring contact performance in order to enable optimal design of brushes for homopolar machines.
At the interface between a brush and a slip ring, where transfer of electric current occurs, factors that affect wear include the spatial distributions of electric current, magnetic field, temperature, and electromagnetic forces as the brush slides at a given velocity on an imperfect rotor (slip-ring) surface. There is experimental evidence that wear is not only highly asymmetric between anode and cathode brushes but is also nonuniform within the contact area of an individual brush. The asymmetry and nonuniformity of wear limits the life and efficiency of a brush assembly, inasmuch as the full volume of brush fiber material is not fully utilized. Moreover, debris from worn brushes can give rise to internal short circuits and/or other adverse effects on the operation of a machine containing a brush assembly.
Each of the two models in the computational- simulation study was a half-symmetric finite-element model representing eight stator brushes, an electromagnet coil, a slip ring, and buses (see figure). The two models differed in the aspect ratios of the brushes (1:2 versus 1:3). The brush contact area was kept constant at 2 cm2, a transport current of 325 A was considered to be applied to each brush, and the current applied to the electromagnet coil was chosen to produce a magnetic flux density of 0.4 T at the brush locations. Coupled electromagnetic and thermal behaviors (including bulk ohmic heating) were included in the simulations. Local adiabaticity and a specific form of the temperature dependence of electrical conductivity were assumed. Time-dependent spatial distributions of electric current, temperature, and electromagnetic force were calculated. The conclusions drawn from the numerical results include the following:
- Circumferential components of electric current at leading and trailing edges of brushes could interact with the magnetic field to produce forces tending to destabilize the brushes, but these forces could be reduced through appropriate design.
- A brush having a higher aspect ratio is subject to smaller destabilizing forces.
- Power loss per brush due to bulk ohmic heating is about 0.74 W for an aspect ratio of 1:2 vs. 0.72 watts for an aspect ratio of 1:3.
- Assuming a contact pressure of 2 psi (≈14 kPa) and a tip speed of 12 m/s, frictional heating is about 16.5 W per brush.
- The power loss per slip ring due to bulk ohmic heating is about 0.98 W for an aspect ratio of 1:2 vs. 0.9 W for an aspect ratio of 1:3.
This work was done by Kuo-Ta Hsieh of the University of Texas at Austin for the Naval Research Laboratory.
NRL-0018
This Brief includes a Technical Support Package (TSP).
Simulations of Brush Contacts of Homopolar Motor/Generators
(reference NRL-0018) is currently available for download from the TSP library.
Don't have an account? Sign up here.
Top Stories
INSIDERManned Systems
Turkey's KAAN Combat Aircraft Completes First Flight - Mobility Engineering...
INSIDERMaterials
FAA Expands Boeing 737 Investigation to Manufacturing and Production Lines -...
INSIDERImaging
New Video Card Enables Supersonic Vision System for NASA's X-59 Demonstrator -...
INSIDERManned Systems
Stratolaunch Approaches Hypersonic Speed in First Powered TA-1 Test Flight -...
INSIDERUnmanned Systems
Army Ends Future Attack and Reconnaissance Helicopter Development Program -...
ArticlesEnergy
Can Solid-State Batteries Commercialize by 2030? - Mobility Engineering...
Webcasts
AR/AI
From Data to Decision: How AI Enhances Warfighter Readiness
Energy
April Battery & Electrification Summit
Manufacturing & Prototyping
Tech Update: 3D Printing for Transportation in 2024
Test & Measurement
Building an Automotive EMC Test Plan
Manufacturing & Prototyping
The Moon and Beyond from a Thermal Perspective
Software
Mastering Software Complexity in Automotive: Is Release Possible...