Features

Modern radar systems are complex and depend heavily on advanced signal processing algorithms to improve their detection performance. At the same time, the radio front-end must meet challenging specifications with a combination of available components, implementation technologies, regulatory constraints, requirements from the system, and signal processing. This application example shows how NI's Visual System Simulator™ (VSS) system simulation software enables radar system architects and RF component manufacturers to design, validate, and prototype a radar system.

The project in this example, Pulse_Doppler_Radar_System.emp, illustrates key models and simulation capabilities available for practical radar design. The project and resulting measurements highlight how to configure a pulse-Doppler (PD) radar and set up the simulation to obtain the metrics of interest for radar development. The entire PD radar system project includes a linear FM (LFM) chirp signal generator, RF transmitter, antennas, clutter, RF receiver, moving target detector (MTD), constant false alarm rate (CFAR) processor, and signal detector for simulation purposes.

Theory of Operation

PD radars produce velocity data by reflecting a microwave signal from a given target and analyzing how the frequency of the returned signal has shifted due to the object's motion. This variation in frequency provides the radial component of a target's velocity relative to the radar. The radar determines the frequency shift by measuring the phase change that occurs in the electromagnetic (EM) pulse over a series of pulses. By measuring the Doppler rate, the radar is able to determine the relative velocity of all objects returning echoes to the radar system, including planes, vehicles, and ground features.

As the reflector (target) moves between each transmit pulse, the returned signal has a phase difference or phase shift from pulse to pulse. This causes the reflector to produce Doppler modulation on the reflected signal. For example, assume a target at a distance R has a radial velocity component of Vr. The round-trip distance to target is 2R. This is equivalent to 2R/ wavelengths or (2R )2/ 4=R /radians.

If the phase of the transmitted signal is φ0, then the phase of the received signal will be:

φ = φ0 + 4πR/λ

The change in phase between pulses is:

dφ/dt = (4π/λ)*(dR/dt) = (4π/λ)*Vr

System Setup

Figure 1. VSS main radar system diagram showing linear chirp source, RF transmitter and receiver links, target and propagation model, and receiver baseband signal processing blocks. Click herefor full-size image.

The main radar system diagram in Figure 1 includes the following building blocks: linear chirp source, RF transmitter and receiver, and target and propagation models, as well as receiver baseband signal processing blocks, including moving target indicator (MTI), MTD, and CFAR. User-defined parameters specifying the gain, bandwidth, and carrier frequency of both the transmitter and receiver sub-blocks can be set to values based on test specifications. A detailed look at the individual components explains how this PD radar works.

Figure 2. Control parameters defining the linear chirp generator output signal.

The linear chirp source (first block to the far left of the system diagram) generates a linear FM chirp signal, also known as a PD signal. The linear chirp pulse source consists of basic parameters that can be configured according to user specifications, such as pulse repetition frequency (PRF), pulse duty cycle, start/stop frequency, and sampling frequency. The pulse repetition interval (PRI) denotes the time difference between the starts of two consecutive pulses, shown in Figure 2. The chirp duration (pulse on) is a function of duty cycle and PRI and is calculated as the product of the two; the duty cycle is a percentage and can take any non-negative value up to and including 100 percent.

During the active portion of the chirp, this block outputs a signal with instantaneous frequency that changes linearly between the start and stop frequency parameters. These two parameters can have any valid frequency value, resulting in signals that can have either increasing or decreasing frequencies at the start of the chirp. Designers are also able to specify the ratio of rise and pulse on. This parameter is a percentage and can have any non-negative value up to and including 100 percent.

The signal power during the active portion of the chirp is set by the peak power parameter of the linear chirp signal generator. A non-zero initial delay may be defined for the chirp pulse; this delay may take on any non-negative value and a warning is generated if this delay is greater than the PRI. The center frequency of the chirp signal may be user defined. If left empty, it is set to the average of the start and stop frequencies. Similarly, the sampling frequency may also be user defined; if left empty, it is calculated based on the global variable “_SMPFRQ”. In this example, the chirp signal level is set to 0 dBm, PRF = 2 kHz and DUTY = 25 percent.

The next block in the chain, a coupled correlator block, is commonly used for pulse compression in radar receivers. Pulse compression is a signal processing technique used to increase the range resolution, as well as the signal-to-noise ratio (SNR), by modulating the transmitted pulse and then correlating the received signal with the transmitted pulse. In this example, a block performs a correlation between the signal reflected from a radar target and the transmitted signal. This requires the coupled correlator to buffer enough samples to accommodate a full PRI before it can process the chirp. To ensure a successful simulation of such scenarios, the sampling frequency should be carefully selected. The minimum value for the sampling frequency parameter would be the bandwidth of the radar signal (FSTART-FSTOP). If spectral measurements are desired, the sampling frequency can be set to a larger value.

Figure 3. Components defining the RF transmitter subcircuit include an oscillator (tone source generates one or more sinusoidal tones), mixer (upconversion), filter, and amplifier. Click herefor full-size image.

The signal next passes through the RF transmitter responsible for frequency up-conversion, filtering, and signal amplification before being radiated through the antenna toward the target. Both the RF transmitter and receiver subcircuits define the single stage upconverter and downconverter that are each composed of an oscillator, mixer, amplifier, and filter, as shown in Figure 3. Users may replace these subcircuits with their own particular implementations. To fully model the entire system, this example includes a subcircuit that models the propagation channel between TX/RX antennas, as well as the radar target. With this particular setup, users may specify the distance and relative velocity of the target, their RCS and RCS fluctuations, and also model jammers and clutter that are often present in radar systems.