Analysis of Voltage and Current Signal Processing in a Li-ion Battery Management System

Performance of Li-ion batteries can be improved using a system that manages their charge and discharge.

A Battery Management System (BMS) manages Li-ion batteries in a storage system for pulsed power weapons aboard Naval vessels. The system charges the batteries with a buck converter according to the Constant Current Constant Voltage method. The BMS uses analog equipment to measure signals and then digitally converts signals for transmittal to a Field Programmable Gate Array (FPGA).

Functional diagram of the BMS. At its core, the BMS is made of four FPGA-controlled buck converters. There is one converter for each battery.
Software processing controls the voltage and current directed to the batteries to maintain proper control and maintenance of the batteries. The BMS’s design can manage the charge and discharge of four Li-ion batteries. The discharge simulates the rapid power consumption by a pulsed power supply.

At its core, the BMS is made of four FPGA-controlled buck converters. There is one converter for each battery. Additionally, each converter contains sensors and a control system to allow for digital control of the buck converter by the FPGA. The FPGA varies the buck converter’s duty cycle to control the battery current.

The BMS is a complex system with many components that work together to accomplish its goal to manage Li-ion batteries. In order to control the charge delivered to Li-ion batteries, the cell current and voltage must be closely monitored. These two sensors are critical components of the BMS operation.

The BMS system consists of a transformer rectifier, a buck converter, an FPGA controller, a data acquisition system, and Li-ion batteries. The components that handle the current signal are a Hall Effect Sensor, a buffer/amplifier, an Analog-to-Digital Converter (ADC), and the FPGA. The components that handle the voltage signal are the voltage-to-frequency converter, an optocoupler for galvanic isolation, a SIMULINK® model for processing the output from the voltage-to-frequency converter, and the FPGA.

For the current signal, two sets of data were collected for analysis; one set with the buck converter operating at 30 kHz, and the other set at 8 kHz. For each frequency, testing included measurements at 20%, 50%, and 80% duty cycles. The digital waveforms are significantly distorted in shape from the analog input. Despite this distortion, the DC component of the signal is only slightly disturbed. The proportional integrator controller of the buck converter corrects the waveform distortion. The controller integrates the signal twice before processing. This smoothes out the signals and extracts the intact DC value of the signals. As the DC component of current is what charges the battery, this processing is appropriate. Therefore, even though the digital conversion introduces significant error, the FPGA does not see the error and uses only the correct DC values for processing.

The voltage signal processing method is less complicated, as the signal is converted digitally when the voltage-to-frequency converter measures it. The converter’s output is a digital square wave with frequency proportional to the voltage. The BMS uses three components to acquire and process the current for use in the FPGA: the LEM sensor, the buffer/amplifier (operational amplifier, or OPAMP), and the ADC.

The voltage output of the buck converter has a much simpler path to the FPGA. The voltage-to-frequency converter measures and digitally converts the voltage signal to a digital square wave with frequency proportional to the measured voltage. The FPGA then converts this digital waveform to a scalar value. The control aspect of the FPGA uses this scalar value to control the operation of the BMS.

The BMS uses a buck converter to deliver power to the Li-ion batteries for charging. The buck converter offers several advantages over other topologies including simplicity, ability to handle a wide range of voltages and currents, and high efficiency. The buck converter used in the BMS uses a MOSFET switch operating at 30 kHz controlled by the FPGA. The FPGA varies the duty cycle of the MOSFET switch to control the output current and the battery voltage. The charging current is constant until the battery voltage reaches an almost-full charge level. After the voltage reaches this level, the battery is trickle charged while regulating the voltage so as not to exceed the maximum battery voltage.

The testing results showed that, when properly calibrated, the BMS properly measures and transmits voltage data to the FPGA for processing and control. The current signal undergoes significant waveform distortion during the digital conversion. The DC component remains intact. The buck converter’s PI controller properly deals with this distortion by slowly responding to rapid changes in current. This allows the controller to respond only to the correct DC component of the current signal.

This work was done by Jerome Sean McConnon of the Naval Postgraduate School. NRL-0047



This Brief includes a Technical Support Package (TSP).
Document cover
Analysis of Voltage and Current Signal Processing in a Li-ion Battery Management System

(reference NRL-0047) is currently available for download from the TSP library.

Don't have an account? Sign up here.